Main Index 1 Mar 2004 @ 08:38:03 UTC Not logged in.  Log In  

Subject: Yaesu FT-50R Guide V 1.1
From: childers@garlic.com (Bill Childers)


The (In)Complete Guide to the Yaesu FT-50 Version 1.1

Compiled by Bill Childers, KE6VVW

Disclaimer & Other Nonsense
The information in this document is a guide to the FT-50 ONLY.  
Having had more than a few radios in my amateur experience, I 
understand how most hams wish to learn as much about their rigs as 
possible.  I have compiled this guide to allow other people to 
learn more about the radio without having to search all over for 
information.  I do not guarantee the validity of this information, 
as Yaesu may change programming or hardware so that some of the 
techniques in this document may cease to function.  I am not 
responsible if these instructions damage your rig in some way.  All 
I can say is that I have performed the following procedures to my 
unit, and I am quite pleased with the results.  Your mileage may 
vary, etc.

 
History

Version 1.0
1st introduced.

Version 1.1
Added: Game mode, Changed High Power Mod to "Internal System 
Alignment".  In this section I also detail the squelch and S-meter 
adjustments.  Also added info to the bug on the FTT-12 Keypad.



Introduction
The Yaesu FT-50 is perhaps the most unique VHF/UHF Handheld 
manufactured today.  Itüs made to MIL-SPEC 810, for dust, 
splashproofness, and vibration.   Out of the box, it has not only 
dual band 2m/440 capability, but wide FM receive and AM receive as 
well.  In addition, it receives 76-200 MHz, 380-500 MHz, and 
700-900 MHz (Cellular Blocked).  It has one of the fastest scan 
speeds for an amateur HT.  It also has the unique ability (w/ 
ADMS-1C software) to interface with an IBM PC running Windows and 
have memories and settings uploaded/downloaded.  In addition, it 
has DCS (digital coded squelch), ARTS (auto-ranging transpond 
system), and Yaesuüs excellent transmit and receive battery saver 
features.  It also uses Yaesuüs extremely efficent FET power module 
that allows for 5W+ of output power with a 9.6V battery pack.  With 
the optional FTT-12 keypad, the unit also performs CTCSS decode, 
DTMF paging, and also incorporates a Digital Voice Recorder!   All 
of this functionality in such a small package makes it my rig of 
choice.

Problems (Bugs)
Unfortunately, the FT-50 is plagued by a few bugs.  None of them 
are very serious or life-threatening, just a bit annoying.   First 
among them is its Wide-FM receive.  Apparently Yaesu engineers 
didnüt put a wide enough filter in the unit, and some of the 
bandwidth of broadcast FM signals gets "chopped off".  This means 
that the rig is near useless for listening to music on the 
broadcast FM band.  It works marginally with voice only on the same 
band.  My opinion on this problem:  If you want to listen to music, 
bring a small Walkman or other transistor radio with you.  The ü50 
does an adequate job of bringing voice signals in on broadcast FM, 
so itüs good for listening to emergency broadcasts.
The second "bug" lies in the optional FTT-12 keypad.  The manual 
for the radio states that you can set up a "voice mail" type of 
functionality that lets your radio operate unattended and record 
calls for you.  This mode doesnüt work correctly, although the 
built-in voice recorder works great. It seems that the unit will 
playback the wrong voice partition. The problem appears to be in 
the DTMF page-answer-back area.  If youüre buying the ü50 and 
FTT-12 solely for this purpose, DONüT!  It doesnüt work and thereüs 
no current workaround.
The third bug has been complained about a bit.  It seems that some 
þ50s suffer from a low Tx audio problem.  This is due to a factory 
adjustment that is set a bit on the low side.  It is easily fixed. 
(See Factory Adjustments below).
The fourth "bug" is synergistic with the ADMS-1C software.  If 
there is some kind of problem in downloading a file to the radio, 
the software aborts with an error, and the rig is left with itüs 
memories cleared in a "limbo" state.  This state is actually the 
European band plan, and if done properly, the rig can be modified 
to receive even more frequencieså  which will be described later. 
(See modification section)  However, if you want to return the rig 
to its natural state, simply download a blank frequency file 
(NONAME.RDF) to the unit.  All should be well.

Factory adjustments
If your rig suffers from the low Tx audio problem, hereüs how to 
fix it.

1. Remove the battery and antenna.
2. Remove the "NiCd" sticker on the heat sink.  If you remove it 
very carefully, itüs possible to re-install it later with the same 
stickum thatüs on it.
3. Look in the cavity where you removed the sticker.  Proceeding 
from left to right, hereüs what youüll seeå
	Phillips head Screw (Holds the keypad in)
	Small Silver Potentiometer (VR1001°VHF Deviation 
Adjustment)
	Small Silver Potentiometer (VR1002°UHF Deviation 
Adjustment)
	Small White Potentiometer (TC1001°DONT TOUCH!  CTCSS Tone 
Adjustment!!!)
	Phillips head Screw (Holds the keypad in)
4. Take a small Phillips head Screwdriver and turn both VR1001 and 
VR1002 about 1/8 turn clockwise.  This will increase the VHF and 
UHF deviation and fix the low Tx audio problem.  If itüs not enough 
Tx audio, simply turn both pots another 1/8 turn.  Make sure to 
turn both pots the same amount!
5. Replace the NiCd sticker, battery, and antenna.
6. Youüre Done!

Internal System Alignment (May not work on some radios)
NOTE: This setting appears to work on radios that have NO MEMORIES 
programmed.  You might want to try STEP 3 before clearing your 
memories.  If step 3 doesnüt work, you probably need to clear your 
memories.  BE CAREFUL with these settingså itüs possible to really 
mess the rig up by setting some funky squelch or somethingå you 
might want to write the default settings for your rig down.

1. Select 2m VFO frequency.
2. Turn the radio off.
3. Push LAMP, PTT, Knob, and PWR at the same time.  The rig will 
turn on with the squelch open, so turn the volume down!
4. The ü50 will display "BAND  xxxxxx" where xxxx may differ 
depending on your radio and whatever mods you may have performed.
5. Turn the top knob. There are a variety of settings available.  
Here is a listing of them:
ù HSSQ: Squelch Hysteresis Adjustment, adjusted by the dial.
ù THSQ: Squelch Preset Threshold
ù TISQ: Squelch Preset Tight
ù S1LV: Low-Scale S-1 Adjustment.
ù S9LV: S-Meter Full Scale Adjustment.
ù HIPO: Hi Transmit Power Adjustment: Should be calibrated for 5W 
(Can be pushed higher with a 13.8V Supply)
ù L3PO: Level 3 Power Adjustment:  Should be adjusted for 2.8W.
ù L2PO: Level 2 Power Adjustment: Should be adjusted for 1W.
ù L1PO: Level 1 Power Adjustment: Should be adjusted for .1W.
6. Select the adjustment you wish.
7. Push in the Top knob.  There will be a "s" that appears next to 
the displayed number.
8. Rotate the knob to change the setting.
9. Change other settings, if desired.  
10. Push the knob for more than 1 sec to save the profile.
11. Select 440 VFO frequency.
12. Repeat Steps 3-10 to adjust the UHF Settings. UHF Settings will 
have a "U" in front of them.


Modifications
The FT-50 is extremely easy to modify.  The first modification is 
performed for you at the factoryå but for those of you who 
accidently disabled it, or changed itå here it is.

Extended U.S. Receive Mod (Expands receive from 144-148 & 430-450 
to 76-200, 380-500, 800-999 þcell 	blockedü) NOTE: All 
memories will be erased.
1. Turn the transceiver off.
2. Hold down the Knob and Lamp keys while powering the unit on.
3. The unit now has U.S. Extended Receive.

 MARS/CAP mod (Extended Transmit Mod: app. 144-159, 420-470) NOTE: 
All memories will be erased.  
Donüt transmit on bands that youüre not licensed for!!  Besides 
being illegal, it creates problems for people using those 
frequencies.
1. Remove battery & antenna
2. Remove NiCd Sticker on Rear Heat Sink
3. Loosen (Donüt Remove) Philips head screws on rear that hold 
keypad in.
4. Use screws as thumb holds to press keypad out.
5. Remove screws.
6. Remove Keypad.
7. Under Keypad on Left Side there is a series of Solder Jumpers.  
They are labeled in white from 1-3.  Only #1 will have solder 
jumpering it.  Remove the solder, being careful not to damage or 
touch any other components.  WARNING:  If youüre not good at 
desoldering, or have shaky hands, you might want to have someone 
else do this for you.  Itüs REAL easy to damage the rig.
8. Reinstall Keypad.  Be careful of the O-ring around the keypad.  
Make sure itüs not twisted or damaged, as the waterproofness of the 
unit could be compromised.
9. Install sticker, battery and antenna.
10. Hold down Knob and Lamp keys while powering the unit on. 
(Extended Receive Mod as above.)
11. Completed!

Super-Hyper Awesome Modå The mother of all Mods!!!  (Requires 
ADMS-1C software and MARS/CAP 	mod to be performed)
Receive: 76-999 Mhz (No displayable holes!!!)
Transmit: 120-221 Mhz, 320-499 Mhz  (AGAIN, Donüt transmit on 
frequencies where youüre not licensed)
NOTE: This mod will disable ARS (automatic repeater shift) and will 
set 2m and 440 repeater offset to 
	weird numbers.  Make sure you enter repeater offset and +- 
shift manually.  Repeater offset needs 
	be set once for the rig, then it should be able to be 
forgotten about.  It will also clear memories.
Remember above where I mentioned the ADMS-1C software having a bug? 
 Hereüs where the enterprising and curious ham can take advantage 
of that.  This mod will install the European band plan in your 
radioåso without the MARS/CAP mod you will lose the top portion of 
your 2m band.
1. Are there frequencies in your radio?  Donüt want to lose them?  
Simply get the data from your radio as it sitså you can "merge" the 
frequencies later.  Save the file.
2. Perform the MARS/CAP mod as outlined above.  Get the data from 
the mod and name it USA.RDF.
3. Attempt to send the same data to the radio.  In the middle of 
the transfer (around 50%), pull the adapter cable to the PC out of 
the radio.
4. Thanks to the bug, your radio is now in European mode!  Perform 
the Extended Receive Mod by holding the Knob and Lamp keys down 
while turning the unit on.
5. Now, the Automatic Repeater offset doesnüt work.  Thereüs no 
workaround.  Note that the 2m offset has been changed to 0.00.  Go 
to the menu by holding down the knob.  Go to SHFT, Option 7.  Press 
the knob.  Turn the knob so that it reads 0.60.  Press PTT.
6. Now, turn off the radio.  Put it back into clone mode.  Read the 
data back from the radio to the PC and save the file as EURO.RDF.  
7. If you want to enter frequencies manually or using ADMS as 
normal, go ahead.  Everything should work.  If you saved 
frequencies as above, open EURO.RDF and "merge" the frequencies 
from your USA.RDF file into it, and save it as another name.  Then 
send the modified EURO.RDF (your filename) file back to the radio 
using the "template" file EURO.RDF.  Youüre done!
8. To return the radio back to the U.S. band plan, send the USA.RDF 
file back to it.
Note that I have no way of measuring the sensitivity of the 
frequencies or the output power of the rig outside of the ham 
bands.  The 220 coverage seems to be very poor, however, the radio 
does display 220 frequencies.  It wonüt transmit on our 220 bands, 
though.  800 Mhz receive is vastly improved.

Game Mode
The FT-50R includes an interesting "game" thatüs programmed into 
it.  Hereüs how it works:
1. Power up the radio while holding down the MR key. (PWR + MR).
2. The display will show GAME on the left side, and Spd 1 on the 
right.  Youüre in game mode!
3. By rotating the knob, you can change the speed of the game.  
Higher numbers are faster.
4. Press PTT to start the game.
5. Numbers will start to scroll across the screen from 
left-to-right.  As they come, you are supposed to push the number 
on the keypad that makes a sum of ten, followed by F.  Example:  6 
appears, press 4, F.  If 0 appears, enter 10 followed by F.
6. The game is over when the screen fills up with numbers.
7. To exit the game, simply cycle the power.

 

Return to the mods-e-h file section.