From: wa2ise@cbnewsb.cb.att.com (robert.f.casey)
Subject: TS940s erratic display or control fix
Date: 8 Dec 91 19:23:45 GMT
Sender: news@cbfsb.att.com


copied from packet:

 Msg# TSF  Size #Rd  Date  Time From   MsgID        To
 8594 BF   3105   0 01-Dec 2326 KD2EJ  27873_WB2QJA INFO@ALLBBS ()
 Sb: TS-940 ERATIC DISPLAY INFO.

SB-951
TS-940S ERRATIC D  01/20/89

Intermittent control or display problems that are difficult
to correct with the reset procedure may be caused by a
faulty ROM socket. The socket should be checked to insure
that it makes good electrical contact with each pin of the
ROM. If it is found to be intermittent, remove the socket
and solder the ROM directly to the board. It should be
noted that units between serial numbers 701XXXX to 811XXXX
and from 903XXXX to 909XXXX are not likely to have this
failure. In addition, units with a serial number of 909XXXX
and above do not incorporate a socket.


CAUTION

Removing the socket requires good soldering skills. The ROM
is mounted on the Digital A unit and is designated as IC2.
The board, being double sided, has solder connections on
both component and foil sides. When the socket is removed,
it is very important to insure that each pin is completely
solder free. Having to pry up on the socket means that it
is not completely desoldered and will cause the circuit
foils to tear.

When performing any work on the Digital A board, CMOS
handling techniques must be observed. Such techniques
include using a grounded or isolated soldering tip, avoid
touching the pins of IC chips with your fingers, and ground
yourself with a wrist ground strap.

To remove the socket:


1Disconnect the power cord and antenna coax.

2Remove the top and bottom covers from the transceiver.

3Remove the 2 flat head screws from each side of the
front panel chassis.

4Loosen the round head screw on each side of the front
panel chassis.

5Carefully rotate the front panel forward. It will be
necessary to unplug the VS-1 cable from the transceiver.

6Remove the 4 screws from the speaker mount.

7Carefully pull up on the mount and rotate it toward the
front panel. Swing the mount toward the right side of
the transceiver and allow it to rest on the Digital B
unit shield.

8Remove the 8 screws from the Digital A unit shield
plate.

9Lift the plate and rotate it to the left side of the
transceiver.

10While avoiding contact with the pins, remove the ROM
(IC2) and set it aside on anti-static foam.

11Remove the 6 screws that mount the Digital A board.
Rotate the board toward the front panel to expose the
bottom side of the board.

12Carefully desolder the socket and remove it from the
board. Do not pry up on the socket. If it does not
easily pull off the board, the top foils are still
soldered to the socket.

13Install the ROM in the board and solder it in place.

14Assemble the transceiver by reversing steps 1 - 11. Do
not pinch the power switch cables between the front
panel and the body of the transceiver.
Time required for this modification is 1.5 hrs or less. (C)
 011189TKC
==================================================================
Note: you might find it easier to break apart the plastic of the
socket and remove the pins one by one. And/Or use a better grade of
socket. 
Try just removing and reinserting the Rom in its socket to see
if this fixes the problem before you go to all this trouble. This
might clean a dirty socket contact.    Anyway....
I haven't tried or verified this, proceed at your own risk. WA2ISE

Kenwood TS-940S
---------------
I'm afraid I've deleted the original request from a 'VK' from a month
or so ago regarding general coverage Tx on a Kenwood TS940S.  Out of
interest I've done some invesigation and an experiment and it seems to
produce the required result.

Here goes..
Remove the bottom cover Locate the 'Control' PCB. (The rearmost
board).  Find PL17/SK17 - a 5 pin 'harmonica' type - about midway along
the forward edge of the board.  Remove the connector and release the
individual socket that connects to pin 5 (nearest to the front edge of
the board). This can be done by depressing the barb on the socket
through the hole in the 'harmonica' moulding and pulling gently on the
wire.  Once removed replace the connector and insulate the, now
floating, removed wire and socket.  Replace the bottom cover.  (To
remove the mod - just replace the socket into the moulding).  In the
experiment the rig produced full output power ( >100W into 50ohm dummy
load) over the range 1.5 to 29.999 Mhz without use of the tuner. When
the tuner was enabled it managed to 'tune' the rig into the same 50ohm
load over the full range. How it would perform into any other load is
unknown.  Not suprisingly, I haven't managed to get it to Tx down to
73kHz in fact below 1.5Mhz the Tx is disabled.  I hope this reaches the
originator of the request.  Regards, Roger.  

G8IUC @ GB7TUT   QTH   London. E4 7DX. UK.  

Msg created 21:19 (local) on 20 Aug 96 using WinPack V5.4