MAR-4SM
Frequency
MHz		 GAIN, dB Maximum Power, dBm Dynamic Range VSWR Absolute
Maximum
Rating		 DC Power Thermal
resistance
Øjc
°C/W
fL - fU Min. Output
(1 dB
Comp.)		 Input
(no
damage)		 NF
dB
Typ.		 IP3
dBm
Typ.		 In
Typ.		 Out
Typ.		 I
(mA)		 P
(mW)		 Cur-
rent
(mA)		 Volt(V.)
DC-1000 7.00 +12.50 +13.00 7.00 25.00 1.50 1.90 85.00 500.00 50.00 5.30 100.00
Lw=low range(fL to fU/2)  U=upper range(fU/2 to fU)

Pin Connections
Port RF in RF Out DC Case GND Not Used
cb 1 3 3 2,4 -



Case Style - WW107 (inch,mm )   weight: 0.015 grams.
A B C D E F G H J
.012
0.305		 .10
2.540		 .020
0.508		 .092
2.337		 .085
2.159		 .060
1.524		 .007
0.178		 .026
0.660		 .235
5.969
K L M N P Q R S T
.118
2.997		 .235
5.969		 .118
2.997		 .072
1.829		 .040
1.016		 .020
0.508		      
Tolerance: .x ± .1  .xx ± .03  .xxx ± .015 inch.
Material and Finish:
    Case material: plastic. Lead Finish: tin-lead plate.
Marking:
    RF input lead (1) identified by one or both of the following at factory option:
(a) diagonally cut lead, which may be 45°(ref) in either direction;
(b) orientation mark on the case. Model dash number identified by color dot or alphanumeric code on case. See specification data sheet.
Packaging:

Packaging information:
Tape Width(mm): 12
Reel Size(inches): 7
Device Cavity Pitch(mm): 8
Devices Per Reel: 1000

 Notes:
• Minimum gain at highest frequency. Full temperature range, except room temperature for Dash-4 models.
• Frequency at which output power, NF and IP3 are specified: 1000 MHz.
• Thermal resistance Øjc is from hottest junction in the device to the mounting surface of the leads.
• Model number designated by alphanumeric code marking.
• Permanent damage may occur if any of these limits are exceeded. These ratings are not intended for continuous normal operation.
• For Amplifier Selection Guide, please click here.
For Amplifier Environmental Specifications, please click here.
• For Surface Mount Environmental Specifications, please click here.
Re-flow soldering information is available in "Surface Mount" article.
• Low frequency cutoff determined by external coupling capacitors.
• Non-hermetic
• Typical Biasing Configuration ERA/MAR/MAV/RAM/VAM
• Prefix letter (optional) designates assembly location.
• Reliability predictions and normal operation conditions are applicable at current specified.
• General Quality Control Procedures and Environmental Specifications are given in Mini-Circuits Guarantees Quality.
Hi-Rel, MIL description are given in Hi-Rel and MIL
• Prices and Specifications subjects to change without notice.

FREQ
(MHz)		 S11 (Input Return Loss) S21 (Power Gain) S12 (Isolation Out-in) S22 (Output Return Loss)
dB Mag Ang dB Ang dB Mag Ang dB Mag Ang
100.00 -14.42 0.19 177.00 8.20 174.00 -15.92 0.16 0.00 -20.00 0.10 -14.00
500.00 -14.89 0.18 169.00 8.20 156.00 -15.92 0.16 1.00 -17.72 0.13 -54.00
1000.00 -15.39 0.17 159.00 8.10 135.00 -15.92 0.16 3.00 -14.89 0.18 -94.00
1500.00 -15.39 0.17 157.00 8.00 112.00 -15.39 0.17 4.00 -12.40 0.24 -121.00
2000.00 -14.42 0.19 151.00 7.70 90.00 -14.42 0.19 3.00 -11.06 0.28 -145.00
2500.00 -12.40 0.24 159.00 7.60 69.00 -13.98 0.20 -1.00 -9.37 0.34 -165.00
3000.00 -10.17 0.31 151.00 6.90 46.00 -13.15 0.22 -6.00 -9.12 0.35 176.00
3500.00 -8.18 0.39 139.00 6.00 27.00 -12.77 0.23 -11.00 -8.64 0.37 160.00
4000.00 -6.74 0.46 126.00 4.90 8.00 -12.04 0.25 -23.00 -8.40 0.38 147.00