 Part Number MMF0281
The Model 281 Static Locator is a high quality, portable, non-contacting
static meter which will produce consistently accurate readings with ease
and will provide years of trouble-free operation. It will indicate surface
voltage and polarity on objects up to 20kV at a spacing of one inch with
an accuracy of 10% of full scale. Also featured are a push-button to hold
readings and automatic power-down to conserve battery. |
 Part # MMF0207
Modulated for use in ionized environments, this pocket-sized fieldmeter
takes quick, accurate measurements without continual rezeroing. Switch selectable
dual range measures 0 to 1000V at one inch from surface and 0 to 3000V at
four inches, or 0 to 10,000 at one inch and 0 to 30,000V at four inches
on 10X range. Ideal for manufacturing environments where ionization equipment
is in use. |
 Part# MMF0282
Accuracy has never come so easily or inexpensively. Alternating pulsing
beams from two LEDs converge to tell you when the instrument is precisely
1 inch from the target, so its reading is an exact indication of the static
field being measured up to +or- 20kV, and up to +or- 80kV with attenuations.
It features a hold button to freeze the display. The modulated design guarantees
accurate readings even in ionized environments. |
 Stock # MSF0311
The Hand-E-Stat Fieldmeter is an accurate, compact, modulated fieldmeter
used for locating and measuring static charge potentials even in ionized
environments. A ranging light system assures accurate and repeatable measurements,
while both SAMPLE and HOLD buttons assure user friendliness. With a range
of +or- 19.99 kV, the Hand-E-Stat offers an analog output jack for recording
readings. |
Part # MMF0289
Perfect for static surveys, the Model 289 with its Hi-Res Bar-graph
display quickly reads either positive or negative values up to 10kV, or
as low as 100V. Now there's no excuse for letting static buildup cause costly
damage. Integrating proven measurement techniques with the latest technology
you'll want one instantly available wherever static can strike. |
 Part# M257
Probe to surface spacing of 1cm allows greater accuracy when measuring
small targets. Measures electrostatic field strength from 10V to 20kV. Remote
probe allows access to hard to reach places. Modulated for drift free measurements,
it offers analog output for unattended use. |
 Model 244
This small, lightweight instrument measures through a range of +or- 3000volts
quickly (less than 2ms to 1kV), has a four digit display and a +or- 3volt
analog output. It measures the surface potential of insulating, semiconductive
or conductive materials on a small 0.1" diameter spot over a large
area, using patented techniques which assure high-accuracy drift-free measurements
almost independent or probe-to-surface spacing. |
Model 244AL
Designed for contact potential measurements, electrophotographic measurements,
electret measurements, and radiation effects on insulators and semiconductors,
the Model 244AL is a quality instrument for measuring electrostatic surface
potential without physical contact. The Model 260 has a range of +or- 15Volts,
with a surface resolution of approximately 0.1” at a probe to surface
spacing of 0.5mm. |
 Model 279
This is a half rack version of the 244, with selectable recorder output
ranges, kill switch, and LED meter for darkroom usage. |
 Model 263
This is an extremely high speed non-contact electrostatic voltmeter with
a range of +or- 2kV |
 Model 266a
The Model 266a is a portable instrument designed to make accurate, non-contacting
voltage measurements in the range of +or- 1200v. 9volt battery operated
with direct and attenuated outputs for DVM, multimeter or recorder, it features
a hold function to store reading of spacing independent measurements. |
 Model 264
A pocket-sized, portable meter to measure surface resistivity and continuity
of work surfaces to ground, Model 264A features automatic ranging from 10E5
to 10E12 ohms or ohms/sq, with accuracy of + or - one decade. Uses ASTM-
recommended parallel bar sensing probe. Convenient size and 9-volt battery
operation make it ideal for quick and easy checking of materials and work
surfaces in production environments. |
 Model 262a
Model 262A is designed to produce fast, repeatable measurements of both
surface resistivity and resistance to ground. Featuring automatic ranging
from 10E4 to 10E14 ohms or ohms/sq., and + or - 1/2 decade accuracy, Model
262A checks resistivity specifications on static control products such as
ESD shielding bags, static dissipative mats and conductive work surfaces,
and checks continuity of work surfaces to ground. The fully portable, battery-operated
unit provides 8 hours steady use. Conforms to ASTM-D257 standards by using
recommended parallel bar sensing probe and 100V measuring voltage. |
 Model 272a
Model 272A provides fast repeatable measurements of both surface resistivity
and resistance to ground in one versatile instrument. Ranging is automatic
from below 10E4 to above 10E14 ohms/sq. or ohms with + or - 0.1 decade accuracy
typical and applied voltage selectable between 10 and 100 volts. Programmable
default settings include selection of scientific notation or 3-place log
display values. Five pound guarded-ring electrode has compliant silver-impregnated
elastomer contact material and spring-loaded center electrode for excellent
contact. Includes carrying case, charger, and specimen support plate with
insulative surface. |
 Model 283
The 283 digital resistance/resistivity test kit measures resistance between
two points, surface to ground, and surface resistivity in accordance with
ESD Standard S4.1. The units unique LCD alows the user to easily read measurements
directly from the meter. Measurement voltages of 10V and 100V, with resistance
range of 10E3 to 10E12. |
 MMEP307
This 5 # weight set option for the Model 262A provides a weight set which
when used with the 262A allows point to point resistance measurements to
be taken. |
Miniature Surface Probes
We offer a new series of custom, miniature surface resistivity probes
for use with our Models 264, 262A, and 272A. The units are useful in measuring
irregularly shaped objects such as DIP tubes and thermoformed plastic carriers. |
Miniature Guard Ring
0.47"o.d. x 6.0"L probe with 0.1"dia. inner electrode
size |
Point to Point Probe
Consisting of two (2) 0.1" diameter, interchangeable pogos mounted
0.4" center to center.
Each of these probes includes a three foot long cable and appropriate connectors.
Modification and recalibration of resistivity instruments required. |
Model RT-06
The Richmond Model RT-06 measures both surface resistivity and resistance
to ground giving simple, repeatable measurements of conductive, static dissipative,
and insulative surfaces. The meter employs the ASTM-257 method of parallel
bar sensing. |
Model RT-03
The Richmond Model RT-03 measures surface resistance to ground and point
to point resistance using two 5# weights electrode and the new ESD S4.1
specified voltage (10V for conductive and 100V for dissipative). Its analog
scale is autoranging from 10E3 to 10E12 and insulative. |
Model M3
The M3 Wrist Strap Checker is an easy to use, hand held tester for all
types of wrist straps and ground leads. It is a compact, portable unit that
reliably indicates the condition of the wrist strap, ground lead, and interface
to the user's skin. If system resistance is too high (greater than 10 megohm)
or too low (less that 800kilohm) an audible alarm will sound and either
the high or low indicator will light. If system resistance is within the
satisfactory range, the "OK" indicator will light. |
9 V AC / DC Converter for M3
|
Model RT-01
The RT-01 easily measures the resistance of a wristband and cord or heel/toe
grounder (with optional footplate) worn by the operator. The RT-01 tests
the range of 750 kilohms to 10 megohms with European ranges of 900 kilohms
to 35 megohms available. |
 Model 275
The Model 275 Ground System Tester has a low end range of 500kohms, and
a high end of either 10 megohm or 100 megohm. This feature makes it invaluable
as a ground path tester for many components of an ESD safe workstation. |
Model TIFP
This metal footplate and interconnecting cord can be used in conjunction
with Models M3, RT-01, and 275 to perform heel/toe grounder testing. |
Part # MRE0400
The Tester Station is an easy to use test mechanism for personnel grounding
devices. If system resistance is too high (greater than 10 megohm) or too
low (less that 750kilohm) either the high or low indicator will light. An
audible alarm will sound if system resistance is within the satisfactory
range, and the "OK" indicator will light. System comes complete
with tester, footplate, and wall mounting sign with instructions. |
Model M70D
The M70D is designed specifically to provide in-line continuous monitoring
of Dual Line wrist straps, and is flexible enough to allow two operators
and two stations to be monitored at the same time. Resistance is measured
100% of the time through the dual leads providing continuous verification.
The Model M70D is designed to the highest standards, utilizing patented
resistive loop technology for consistent operation. |
Model RT-05
The RT-05 continuously monitors the presence of ground and the continuous
connection of the wrist strap to the operator. The RT-05 provides a constant
capacitive measurement of the operator but a resistive ( up to 2.3 megohm
) constant measurement of ground. At the first sign of a faulty connection,
the red LED will flash and an audible alarm will sound. |
Part # M60a
The M60a Two Station Wrist Strap Monitor System continuously monitors
one or two ESD Work Surfaces and one or two conductive wrist straps to detect
loss of continuity. Conditions such as ungrounded work surfaces or broken
cords and improper wearing by operators are detected instantly to alert
the operator to take corrective action before serious and expensive losses
can occur due to ESD.
The compact M60a independently monitors up to two workstations with a common
control/alarm module. Individual green "status OK" and red "fault"
LEDs for each workstation, operator, and worksurface give continuous indication
of work surface and wrist strap/coil cord grounding status. An audible alarm
sounds to alert the operator when a failure condition is detected. Each
satellite module has an additional grounding jack for a visitor. |
 Model 268
Model 268 provides quick and easy evaluation of ionization equipment
to ESD Association S 3.1. The simple to use unit features two modes of operation.
The normal mode evaluates the effectiveness of room ionization, laminar
flow hoods, table top ionization, and air guns and nozzles as described
in the standard, including static decay timing and system balance monitoring.
The peak mode reads and holds either the positive or negative peak reading
on the charged plate. This is useful for monitoring maximum DC voltage swings
in pulsed DC ionization systems.
Model 268 features two switch selectable ranges -- 0 to + or - 2000V or
0 to + or - 5000V -- with automatically set trip points to begin and end
static decay tests. The isolated charge plate / probe assembly is removable
and is fitted with a tripod mount for easy positioning. |
Model 268-1T
Model 268-1T offers all of the features of the standard Model 268, and
adds the capability of adjusting the low end stop point for timed decay
measurements from 1v to 1000v in 1v increments. |
 Model EA-3
The EA-3 Electrostatic Analyzer is a multipurpose instrument designed
to evaluate the balance and efficiency of ionization equipment such as room
air ionization systems, ionized air blowers, guns and nozzles. It can be
used to evaluate static-protective floor and work surfaces, conductive containers,
anti-static garments and wrist straps, as well as monitor potentials on
the human body.
Designed to ESD S3.1, it offers two preset timed decay, ability to adjust
the low end timer cut-off point, provides X - Y plotter output, and can
be remotely operated. |
 Model 265CPS
Designed for use with the Model 265, the system extends its use to include
a quick and inexpensive means of evaluating the effectiveness of ionizations
systems and other ESD materials. The system comprises a clip-on floating
plate to fit the fieldmeter and a Floating Plate Charger to produce a 1000
volt charge of either polarity on the plate. A carrying case is provided.
The device is invaluable as a survey analyzer to pinpoint ionization units
out of calibration while in use. It should be included in every ESD survey
kit right along with the fieldmeter. |
 Model 282CPS
Designed for use with the Model 282, the 282CPS incorporated the same
features as the 265CPS above.
|
DataStat
The Datastat 2000 is a portable instrument used to record and evaluate
static voltage on people and equipment. It stores information in memory
until downloaded to a computer where it can then be graphed analyzed throught
user-friendly software. Min/max voltages, elapsed decay times and script
can be added to enhance the visual display. |
Model 287IPA
Test any and all ionizers as simply as touching a button! The Model 287
Ionization Performance Analyzer performs manual or automatic decay and balance
tests for periodic verification of ionization equipment. It then stores
the results and averages decay times for up to 10 manual tests and up to
10 complete automatic test sequences. Temperature and relative humidity
are displayed real time and recorded with the test data. |
 Model 284
The Model 284 Nanocoulombmeter offers the ability to make direct measurements
of charge on materials. The material is either dropped into the optional
Faraday Cup where the charge is transferred to the cup and measured by the
meter, or the operator can use an oscilloscope probe to take charge measurements
on smaller objects outside the Faraday Cup. Battery operated with two ranges:
200nC and 20nC.
284/22A
2 5/8" Faraday Cup for Model 284
284/22B
6" Faraday Cup for Model 284 |
Model 910
A completely integrated system for simulating ESD events to determine
the susceptibility level of electronic devices to electrostatic discharge.
With both manual and automatic modes, the fully adjustable, dual polarity
10kV system meets the requirements of MIL STD 883C, Notice 8, Method 3015.7,
with the capability of performing Human Body Model discharge testing up
to +or- 8kV. Plug-in capacitor and resistor modules allow the user to easily
alter the HBM R & C values. The Model 910 interfaces with the device
under test by means of a pair of miniature test leads and the standard plug-in
adapter module. Optional adapter modules are available for unique I/O pin
configurations. |
 Model 930C
A complete system for simulating ESD events to aid in determining the
susceptibility of electronic equipment to electrostatic discharge. The system
utilizes plug-in resistor and capacitor modules to configure the output
to virtually any Human Body Model or Machine Model requirements. The continuously
adjustable, 30kV dual polarity system provides both Auto Count and Free
Run modes of operation. The standard probe tip is a .375" diameter
sphere to simulate the discharge from a human finger. Optional probes are
available to generate instantaneous "H" and "E" fields.
The Simulator and accessories are contained in a sturdy cushioned protective
ABS carrying case for convenient storage and ease of transport. |
 Model 406D
The only complete system available for measuring the electrostatic
dissipation performance of materials in accordance with Fed. Test Method
Std. 101C, Method 4046 and meets all requirements for static decay testing
specified in Mil-B-81705C, EIA-541, and NFPA 99. The Static Decay Meter
is used in both development and quality control applications to test all
material used in static sensitive applications such as electronic component
packaging, clean rooms, hospitals, and hazardous locations. The system is
applicable to testing any material where static electricity can effect its
manufacture, handling, performance or appearance. |
Model 431
The Model 431 Shielded Bag Test System is designed to perform both
the EIA-541 and the ESD S11.31 tests when used in conjunction with the appropriate
user supplied oscilloscope and computer. |
.jpg) Model 267
Model 267 is a simple easy to use device to evaluate electrostatic shielding
capabilities of exposed or buried metalized layers in ESD shielding bags.
Designed for quality control evaluation, incoming acceptance testing, or
checking ESD shielding ability of used bags, Model 267 identifies defective
bags and permits reuse of used bags which have retained electrostatic shielding
integrity. The portable, battery operated unit features a range of less
than 100 to greater the 10E4 ohms per square with 10% accuracy at 1000 ohms
per square. |
 Model 248
This device detects the electric field from a moving charged person or
object with a special multilayer tape sensor. It can trigger any of several
alarm modes if the voltage exceeds a preset level, adjustable from 10V to
10kV. By connecting a counter to a relay output, the user can track the
number of ESD events or charged object intrusions per day. Analog output
for recorders is provided. This device is ideal for workbench monitoring.
The flexible Model 1021 sensor tape can be looped or folded around corners
or doorways. |
Model RT-07
The RT-07 is a unique, battery operated static voltage meter designed
specifically as a visual indicator for showing static built up on a person.
One touch from a finger will trigger a LED showing between zero and 19,999
volts and its polarity. |