1) "MIL-O-55310, Military Specification, Oscillators, Crystal, General Specification for," the latest revision is available from Military Specifications and Standards, 700 Robbins Ave., Bldg. 4D, Philadelphia, PA 19111-5094.
2) CCIR Recommendation No. 686, "Glossary," CCIR 17th Plenary Assembly, Vol. VII, "Standard Frequency and Time Signals (Study Group 7)," (1990). Consultative Committee on International Radio (CCIR); copies available from: International Telecommunications Union, General Secretariat - Sales Section, Place des Nations, CH-1211 Geneva, Switzerland.
3) "IEEE Standard Definitions of Physical Quantities for Fundamental Frequency and Time Metrology," IEEE Std 1139-1988, The Institute of Electrical and Electronics Engineers, Inc., 345 East 47th Street, New York, NY 10017.
4) E. A. Gerber, "Long Term Stability and Aging of Resonators," Precision Frequency Control, Vol. 1, Chapt. 6, pp. 271-284, 1985.
5) "MIL-C-49468, Military Specification, Crystal Units, Quartz, General Specification for," the latest revision is available from Military Specifications and Standards, 700 Robbins Ave., Bldg. 4D, Philadelphia, PA 19111-5094.
6) R. L. Filler, "Aging Specification, Measurement, and Analysis," Proceedings of the 7th Quartz Devices Conference & Exhibition, pp. 93-104, 1985; The Electronic Industries Assoc., 1722 Eye St., NW, Washington, DC 20006.
7) P. T. Landsberg, "On the Logarithmic Rate Law in Chemisorption and Oxidation," The J. of Chem. Physics, Vol. 23, pp. 1079-1087, 1955.
8) I. M. Ritchie, "The Oxidation of Metal Films," Thin Solid Films, Vol. 34, pp. 83-86, 1976.
9) R. Glang, et al., "High Vacuum Technology," in Handbook of Thin Film Technology, L. I. Maissel and R. Glang, editors, McGraw Hill, pp. 2-39 to 2-59, 1970.
10) W. G. Perkins, "Permeation and Outgassing of Vacuum Materials," J. Vac. Sci. Technol., Vol. 10, pp. 543-556, 1973.
11) C. D. Stockbridge, "Effect of Hydrostatic Pressure on Rotated Y-Cut Quartz Crystal Resonators," Vacuum Microbalance Techniques, Vol. 5, Plenum Press, New York, 1966, pp. 179-191.
12) C. D. Stockbridge, "Effects of Gas Pressure on Quartz Crystal Microbalances," Vacuum Microbalance Techniques, Vol. 5, Plenum Press, New York, 1966, pp. 147-178.
13) J. R. Vig and E. Hafner, "Packaging Precision Quartz Crystal Resonators," R & D Tech. Report ECOM-4134, July 1973, AD 763215.
14) R. Abermann, "Measurements of the Intrinsic Stress in Thin Metal Films," Vacuum, Vol. 41, pp. 1279-1290, 1990.
15) R. W. Hoffman, "Stresses in Thin Films: The Relevance of Grain Boundaries and Impurities," Thin Solid Films, Vol. 34, pp. 185-190, 1976.
16) D. M. Mattox, "Thin Film Metallization of Oxides in Microelectronics," Thin Solid Films, Vol. 18, pp. 173-186, 1973.
17) M. Adamov, et al., "Electrical and Structural Properties of Thin Gold Films Obtained by Vacuum Evaporation and Sputtering," Thin Solid Films, Vol. 24, pp. 89-100, 1974.
18) J. G. Vaughan, et al., "Effect of Partial Pressure and Temperature on Properties of Vacuum Deposited Chromium-Gold Thin Films," J. Vac. Sci. Technol., Vol. 20, No. 3, pp. 383-387, March 1982.
19) B. Kebabi, et al., "Stress and Microstructure Relationships in Gold Thin Films," Vacuum, Vol. 41, Nos. 4-6, pp. 1353-1355, 1990.
20) R. Abermann and R. Koch, "Internal Stress of Thin Silver and Gold Films and its Dependence on Gas Absorption," Thin Solid Films, Vol. 62, pp. 195-208, 1979.
21) L. I. Maissel and M. H. Francombe, An Introduction to Thin Films, pp. 200-210, Gordon & Breach Science Publishers, 1973.
22) E. Murr and M. C. Inman, "Effects of Vacuum Environment on the Sub-structure of Evaporated F.C.C. Metal Films," Phil. Mag., Vol. 14, pp. 135-153, 1966.
23) E. Klokholm and J. F. Freedman, "Magnetostress Effects in Evaporated Ni Films," J. Appl. Phys., Vol. 38, pp. 1354-1356, 1967.
24) F. R. Botzen, et al., "Creep of Thin Metallic Films," Vacuum, Vol. 41, pp. 1287-1290, 1990.
25) J. M. Heras and E. E. Mola, "Resistivity Study of the Annealing Kinetics of Thin Evaporated Gold Films," Thin Solid Films, Vol. 35, pp. 75-82, 1976.
26) A. P. Dorey and J. Knight, "The Variation of Resistance of Gold Films with Time and Annealing Procedure," Thin Solid Films, Vol. 4, pp. 445-451, 1969.
27) R. J. Miller and A. Gangulee, "Electromigration in Gold and Copper Thin Film Conductors," Thin Solid Films, Vol. 69, pp. 379-386, 1980.
28) J. D. Wilcock, et al., "The Internal Stress in Evaporated Silver and Gold Films," Thin Solid Films, Vol. 3, pp. 13-34, 1969.
29) C. A. Neugebauer, "Tensile Properties of Thin, Evaporated Gold Films," J. of Appl. Physics, Vol. 31, No. 6, pp. 1096-1101, 1960.
30) L. Eckertova, Physics of Thin Films, Plenum Press, New York and London, 1977, pp. 154-158.
31) H. Hieber, "Aging Properties of Gold Layers with Different Adhesion Layers," Thin Solid Films, Vol. 37, pp. 335-343, 1976.
32) M. Laugier, "Adhesion and Internal Stress in Thin Films of Aluminum," Thin Solid Films, Vol. 79, pp. 15-19, 1981.
33) J. R. Lloyd and S. Nakahara, "Low Temperature Void Growth and Resistivity Decay in Thin Evaporated Gold Films," Thin Solid Films, Vol. 45, pp. 411-420, 1977.
34) E. P. EerNisse, "Quartz Resonator Frequency Shifts Arising from Electrode Stress," Proc. 29th Ann. Symp. on Frequency Control, pp. 1-4, 1975.
35) R. J. Besson, "A New Electrodeless Resonator Design," Proc. 31st Ann. Symp. on Frequency Control, pp. 147-152, 1977.
36) J. R. Norton, "BVA-Type Quartz Oscillator for Spacecraft," Proc. 45th Ann. Symp. on Frequency Control, 1991.
37) G. Majni, et al., "Interdiffusion of Thin Cr and Au Films Deposited on Silicon," Thin Solid Films, Vol. 38, pp. 15-19, 1976.
38) P. H. Holloway, "Gold/Chromium Metallizations for Electronic Devices," Solid State Technology, pp. 109-115, February 1980.
39) Y. E. Strausser, et al., "Observations of Al2O3 and Free Silicon at the Interface Between Aluminum Films and SiO2," Thin Solid Films, Vol. 52, pp. 203-214, 1978.
40) R. J. Blattner and A. J. Braundmeier, Jr., "Solid Phase Reduction of SiO2 in the Presence of an Al Layer," J. Vac. Sci. Technol., Vol. 20, No. 3, pp. 320-323, March 1982.
41) E. Philofsky and E. L. Hall, "A Review of the Limitations of Aluminum Thin Films on Semiconductor Devices," IEEE Trans. on Parts, Hybrids, and Packaging, Vol. PHP-11, No. 4, pp. 281-290, December 1975.
42) J. R. Black, "The Reaction of Al with Vitreous Silica," 15th Ann. Proc. Reliability Physics 1977, pp. 257-260, 1977, IEEE Cat. No. 77 CH1195-7PHY.
43) K. Haruta and W. J. Spencer, "Strain in Thin Metal Films on Quartz," Journal of Applied Physics, Vol. 37, No. 6, pp. 2232-2233, May 1966.
44) V. E. Bottom, "A Novel Method of Adjusting the Frequency of Aluminum Plated Quartz Crystal Resonators," Proc. 30th Ann. Symp. on Frequency Control, pp. 249-253, 1976.
45) C. W. Shanley and L. N. Dworsky, "DC Plasma Anodization of Quartz Resonators," Proc. 36th Ann. Symp. on Frequency Control, pp. 108-114, 1982.
46) J. L. Jellison, "The Role of Surface Contaminants in the Solid-State Welding of Metals," in Treatise on Clean Surface Technology, Vol. 1, ed. by K. L. Mittal, Plenum Press, pp. 205-234, 1987.
47) J. R. Vig, "UV/Ozone Cleaning of Surfaces," in Treatise on Clean Surface Technology, Vol. 1, ed. by K. L. Mittal, Plenum Press, pp. 1-26, 1987.
48) R. L. Filler, et al., "Ceramic Flatpack Enclosed AT and SC-cut Resonators," Proc. 1980 IEEE Ultrasonics Symp., pp. 819-824, 1980.
49) Private communication, M. Bloch (to J. Vig), Frequency Electronics, Inc., May 1991.
50) Private communication, C. Jensik (to J. Vig), Piezo Crystal Co., May 1991.
51) E. Hafner and R. S. Blewer, "Low-Aging Quartz Crystal Units," Proceedings of the IEEE, Vol. 56, No. 3, pp. 366-368, March 1968.
52) Private communications, C. A. Adams and J. A. Kusters, Hewlett-Packard Co. (to J. Vig), May 1991.
53) J. G. Gualtieri, "The Influence of Temperature and Electric Field on the Etch-Channel Density in Swept-Cultured Quartz," Proc. 39th Ann. Symp. on Frequency Control, pp. 247-254, 1985.
54) R. B. Belser and W. H. Hicklin, "Comparison of Aging Performance of 5-MHz Resonators Plated with Various Electrode Metals," Proc. 23rd Ann. Symp. on Frequency Control, pp. 132-142, 1969.
55) J. C. Brice, "Crystals for Quartz Resonators," Reviews of Modern Physics, Vol. 57, No. 1, pp. 105-138, January 1985.
56) M. Hedrickson and J. R. Vig, unpublished, 1991.
57) R. L. Filler, et al., "Aging Studies on Quartz Crystal Resonators and Oscillators," Proc. 38th Ann. Symp. on Frequency Control, pp. 225-231, 1984.
58) P. I. Aseev, et al., "Influence of Surface Catalytic Reactions on Crystal Unit Aging," Proc. 45th Ann. Symp. on Frequency Control, elsewhere in these proceedings, 1991.
59) A. Ballato, et al., "The Force-Frequency Effect in Doubly Rotated Quartz Resonators," Proc. 31st Ann. Symp. on Frequency Control, pp. 8-16, 1977.
60) R. A. Young and C. E. Wagner, "X-ray Source-Image Distortion Technique for the Study of Crystal Distortion and Vibration," Journal of Applied Physics, Vol. 37, No. 11, pp. 4070-4076, October 1966.
61) R. A. Young, et al., "Special X-Ray Studies of Quartz Frequency Control Units," Proc. 19th Ann. Symp. on Frequency Control, pp. 23-41, 1965.
62) D. L. Hammond, "Precision Quartz Resonators," Proc. 15th Ann. Symp. on Frequency Control, pp. 125-138, 1961.
63) Z. D. Jastrzebski, The Nature and Properties of Engineering Materials, 2nd ed., pp. 253-260, 1976.
64) B. Chalmers, Physical Metallurgy, pp. 139-191 and 328-332, John Wiley & Sons., 1959.
65) T. E. Parker, "A New All Quartz Package for SAW Devices," Proc. 39th Ann. Symp. on Frequency Control, pp. 519-525, 1985.
66) E. P. EerNisse, "Temperature Dependence of the Force-Frequency Effect for the AT-, FC-, SC-, and Rotated X-cuts," Proc. 34th Ann. Symp. on Frequency Control, pp. 426-430, 1980.
67) R. L. Filler and J. R. Vig, "The Effect of Bonding on the Frequency vs. Temperature Characteristics of AT-cut Resonators," Proc. 30th Ann. Symp. on Frequency Control, pp. 264-268, 1976.
68) G. L. Dybwad, "Aging Analysis of Quartz Crystal Units with Ti Pd Au Electrodes," 31st ASFC, pp. 144-146B, 1977.
69) J. Crank, The Mathematics of Diffusion, Clarendon Press, Oxford, 1956/1975.
70) American Institute of Physics Handbook, D. E. Gray (ed.), Second Edition, Office of Science Information, National Science Foundation, McGraw Hill Company, New York, 1957/1963, pp. 2-77 and 2-78.
71) L. E. Halliburton and J. J. Martin, "Properties of Piezoelectric Materials," in Precision Frequency Control, Volume 1, E. A. Gerber and A. Ballato (eds.), Chapter 1, pp. 100-106, Academic Press, New York, 1985.
72) M. R. Miljkovic, et al., "Aging Prediction of Quartz Crystal Units," Proc. 42nd Annual Symp. on Frequency Control, pp. 404-411, 1988.
73) L. H. Van Vlack, Elements of Material Science, Second edition, Addison-Wesley Publishing Co., Reading, Massachusetts, pp. 100-106, 1959/1964.
74) J. R. Vig, et al., "Chemically Polished Quartz," Proc. 31st Ann. Symp. on Frequency Control, pp. 131-143, 1977.
75) R. A. Murray, "Movement of Dislocations in Quartz," Proc. 45th Ann. Symp. on Frequency Control, elsewhere in these Proc., 1991.
76) D. W. Hart, et al., "A Study of the Electrodiffusion Process in Quartz," Proc. 44th Ann. Symp. on Frequency Control, pp. 222-227, 1990.
77) F. B. Johnson and R. S. Pease, "The Pile Irradiation of Quartz Crystal Oscillators," Phil. Mag., Vol. 45, pp. 651-654, 1954.
78) W. Primak, "Fast-Neutron-Induced Changes in Quartz and Vitreous Silica," Phys. Rev., Vol. 110, pp. 1240-1254, 1958.
79) R. A. Laudise and R. L. Barns, "Perfection of Quartz and its Connection to Crystal Growth," IEEE Trans. on Ultrasonics, Ferroelectrics and Frequency Control, Vol. 35, pp. 277-287, 1988.
80) H. W. Jackson, "Tactical Miniature Crystal Oscillator," Proc. 34th Ann. Symp. on Frequency Control, pp.449-456, May 1980.
81) R. L. Filler, "The Amplitude-Frequency Effect in SC-cut Resonators," Proc. 39th Ann. Symp. on Frequency Control, pp. 311-316, 1985.
82) F. L. Walls, "The Influence of Pressure and Humidity on the Medium and Long Term Frequency Stability of Quartz Oscillators," Proc. 42nd Ann. Symp. on Frequency Control, pp. 279-283, 1988.
83) F. L. Walls, "Environmental Sensitivities of Quartz Crystal Oscillators," Proc. 22nd Ann. Precise Time and Time Interval (PTTI) Applications and Planning Meeting, NASA Conference Publ. 3116, pp. 465-486, 1990.
84) A. Ballato and J. R. Vig, "Static and Dynamic Frequency-Temperature Behavior of Singly and Doubly Rotated Oven Controlled Quartz Resonators," Proc. 32nd Ann. Symp. on Frequency Control, pp. 180-188, 1978.
85) K. E. Grata, "Long Term Crystal Stability Study," Proc. 5th Quartz Crystal Conference, pp. 214-221, 1983; The Electronic Industries Assoc., 1722 Eye St., NW, Washington, DC 20006.
86) O. N. Efremov, et al., "Aging of Precision Quartz Resonators," Izmeritel'naya Tekhnika, No. 3, pp. 74-75, March 1975.
87) M. I. Jaroslavsky and V. D. Lavrentsov, "Long Term Frequency Variations of Quartz Crystal Units Under Different Environmental Conditions," Ferroelectrics, Vol. 43, pp. 51-56, 1982.
88) A. W. Warner, "Design and Performance of Ultraprecise 2.5-mc Quartz Crystal Units," The Bell System Technical Journal, pp. 1193-1217, September 1960.
89) J. H. Armstrong, et al., "Aging Characteristics of Quartz Crystal Resonators," Proc. 20th Ann. Symp. on Frequency Control, pp. 192-207, 1966.
90) J. Messina et al., "Results of Long Term Testing of Tactical Miniature Crystal Oscillators," Proc. 43rd Ann. Symp on Frequency Control, pp. 207-212, 1989.
91) P. A. Simpson and A. H. Morgan, "Quartz Crystals at Low Temperatures," Proc. 13th Ann. Symp. on Frequency Control, pp. 207-212, 1959.
92) P. A. Simpson and A. H. Morgan, "Investigation of Stability of Quartz Resonators at Low Temperatures," NBS Report 6080, 1959, AD 230714.
93) G. Robichon, et al., "Frequency Stability of Quartz Crystal at Very Low Temperatures: Preliminary Results," Proc. 38th Ann. Symp. on Frequency Control, pp. 201-205, 1984.
94) R. L. Filler, et al., "The Aging of Resonators and Oscillators Under Various Test Conditions," Proc. 41st Ann. Symp. on Frequency Control, pp. 444-451, 1987.
95) R. L. Filler, et al., "Frequency-Temperature and Aging Performance of Microcomputer Compensated Crystal Oscillators," Proc. 43rd Ann. Symp. on Frequency Control, pp. 27-33, 1989.
96) R. J. Byrne and J. L. Hokanson, "Effect of High-Temperature Processing on the Aging Behavior of Precision 5-MHz Quartz Crystal Units," IEEE Transactions on Instrumentation and Measurement, Vol. IM-17, No. 1, pp. 76-79, March 1968.
97) R. C. Smythe and R. B. Angove, "Chemically Milled UHF SC-Cut Resonators," Proc. 42nd Ann. Symp. on Frequency Control, pp. 73-77, 1988.
98) R. L. Filler and R. C. Lindenmuth, U. S. Army Electronics Technology and Devices Laboratory, 1991, unpublished.
99) T. E. Parker and G. K. Montress, "Precision Surface-Acoustic-Wave (SAW) Oscillator," IEEE Trans. on Ultrasonics, Ferroelectrics, and Frequency Control, Vol. 35, No. 3, pp. 342-364, May 1988.
100) A. W. Warner, "Ultra-Precise Quartz Crystal Frequency Standards," IRE Trans. on Instrumentation, Vol. I-7, pp. 185-188, December 1958.
101) W. J. Spencer and W. L. Smith, "Precision Quartz Crystal Controlled Oscillator for Severe Environmental Conditions," Proc. 16th Ann. Symp. on Frequency Control, pp. 405-420, 1962.
102) R. A. Sykes, et al., "Performance of Precision Quartz-Crystal Controlled Frequency Generators," IRE Trans. on Instrumentation, Vol. I-11, pp. 243-247, December 1962.
103) W. J. Spencer and R. L. Reynolds, "Characteristics of Frequency Control Devices for Satellite Environments," in Symposium on Cleaning and Materials Processing for Electronics and Space Apparatus, ASTM Spec. Publ., Vol. 342, pp. 155-163, 1962.
104) A. W. Warner, et al., "Fundamental Studies of Aging in Quartz Resonators," IEEE Transactions on Sonics and Ultrasonics, Vol. SU-12, No. 2, pp. 52-59, June 1965.
105) E. A. Gerber and R. A. Sykes, "Quartz Frequency Standards," Proceedings of the IEEE, Vol. 55, No. 6, pp. 783-791, June 1967.
106) R. J. Besson and U. R. Peier, "Further Advances on B. V. A. Quartz Resonators," Proc. 34th Ann. Symp. on Frequency Control, pp. 175-182, May 1980.
107) R. J. Besson, et al., "Performance of New Oscillators Designed for 'Electrodeless' Crystals," Proc. 34th Ann. Symp. on Frequency Control, pp. 457-462, May 1980.
108) J. R. Vig, "The Effects of Surface Contamination on the Noise and Drive-Level Sensitivity of Piezoelectric Resonators," U. S. Army Laboratory Command R&D Tech. Report SCLET-TR-87-5, May 1987, AD A181299.
109) J. J. Suter and R. H. Maurer, "Low and Medium Dose Radiation Sensitivity of Quartz Crystal Resonators with Different Al-Impurity Content," Proc. 40th Ann. Symp. on Frequency Control, pp.134-139, 1986.
110) L. J. Palkuti and Q. T. Truong, "An X-ray Irradiation System for Total-Dose Testing of Quartz Resonators," Proc. 38th Ann. Symp. on Frequency Control, pp. 55-62, 1984.
111) D. A. Berlincourt, et al., "Piezoelectric and Piezomagnetic Materials and Their Function in Transducers," in Physical Acoustics, W. P. Mason, editor, Ch. 3, Volume 1 - Part A. Academic Press, pp. 201 and 207, 1964.
112) S. Fujishima, "Research and Development of Piezoelectric Devices in Japan," Proc. Ultrasonics Symp., pp. 128, September 1979.
113) "IRE Standards on Piezoelectric Crystals - Measurements of Piezoelectic Ceramics," Proceedings of the IRE, Vol. 49, No. 7, pp. 1161-1169, 1961.
114) R. Lefevre, et al., "Laser Processed Miniature LiTaO3 Resonators and Monolithic Filters," Proc. 39th Ann. Symp. on Frequency Control, pp. 333-337, 1985.
115) J. M. Power, et al., "Long Range Hydrophones," Applications of Ferroelectric Polymers, T. T. Wang, et al., editors, Chapter 6, pp. 128, 1988.
116) E. A. Gerber and R. A. Sykes, "State-of-the-Art Quartz Crystal Units and Oscillators," Proc. IEEE 54, pp. 103-116, 1966.
117) S. Kanbayashi, et al., "Analysis of Tuning Fork Crystal Units and Application into Electronic Wrist Watches," Proc. 30th Ann. Symp. on Frequency Control, pp. 167-174, 1976.
118) J. Engdahl and H. Matthey, "32-kHz Quartz Unit for High Precision Wrist Watch," Proc. 29th Ann. Symp. on Frequency Control, pp. 187-194, 1975.
119) H. Yoda, et al., "Low Power Oscillation for Electric Wrist Watch," Proc. 26th Ann. Symp. on Frequency Control, pp. 140-147, 1972.
120) M. P. Forrer, "A Flexure-Mode Quartz for an Electronic Wrist Watch," Proc. 23rd Ann. Symp. on Frequency Control, pp. 157-162, 1969.
121) H. Yoda and N. Hoie, "Technical Aspects of Wrist Watches," Proc. 28th Ann. Symp. on Frequency Control, pp. 57-66, 1974.
122) D. T. Bell, Jr., "Aging Processes in SAW Resonators," Proc. 1977 Ultrasonics Symp., pp. 851-856, 1977.
123) W. R. Shreve, "Aging in Quartz SAW Resonators," Proc. 1977 Ultrasonics Symp., pp. 857-861, 1977.
124) C. A. Adams and J. A. Kusters, "Improved Long Term Aging in Deeply Etched SAW Resonators," Proc. 32nd Ann. Symp. on Frequency Control, pp. 74-76, 1978.
125) W. R. Shreve, et al., "Fabrication of SAW Resonators for Improved Long Term Aging," Proc. 1978 Ultrasonics Symp., pp. 573-579, 1978.
126) W. R. Shreve, "Active Aging of SAW Resonators," Proc. 1980 Ultrasonics Symp., pp. 188-192, 1980.
127) J. I. Latham and D. Saunders, "Aging and Mounting Developments for SAW Resonators," Proc. 1978 Ultrasonics Symp., pp. 513-517, 1978.
128) M. Gilden, et al., "Long Term Aging and Mechanical Stability of 1.4 GHz SAW Oscillators," Proc. 1980 Ultrasonics Symp., pp. 184-187, 1980.
129) T. E. Parker, "Analysis of Aging Data on SAW Oscillators," Proc. 34th Ann. Symp. on Frequency Control, pp. 292-301, 1980.
130) T. E. Parker, "Development of Precision SAW Oscillators for Military Applications," Proc. 36th Ann. Symp. on Frequency Control, pp. 453-458, 1982.
131) T. E. Parker, "Precision Surface Acoustic Wave (SAW) Oscillators," Proc. 1982 Ultrasonics Symp., pp. 268-274, 1982.
132) E. Simon, "Long Term Frequency Stability of Crystal Oscillators," Technical Report ECOM-2787, December 1966, AD 647742.
133) M. B. Bloch and J. L. Denman, "Further Development on Precision Quartz Resonators," Proc. 28th Ann. Symp. on Frequency Control, pp. 73-84, 1974.
134) Nuclear Energy, pamphlet no. EDM-1016, U.S. Department of Energy, May 1976.
135) T. M. Flanagan, et al., "Evaluation of Mechanisms for Low-Dose Frequency Shifts in Crystal Oscillators," 40th Ann. Symp. on Frequency Control, pp. 127-133, 1986.
136) J. R. Vig, "Resonator Aging," 1977 Ultrasonics Symposium Proceedings, IEEE Cat. No. 77CH1264-1SU, pp. 848-849, 1977.
137) S. Glasstone, Textbook of Physical Chemistry, Second Edition, Seventh Printing, D. Van Nostrand Co., New York, 1940/1951.
138) S. H. Olster, et al., "A6 Monolithic Crystal Filter Design for Manufacture and Design Quality," Proc. 29th Ann. Symp. on Frequency Control, pp. 105-112, 1975.
139) J. R. Gehrke and R. Klawitter, "Experimental Results on Aging of AT-cut Strip Resonators," Proc. 42nd Ann. Symp. on Frequency Control, pp. 412-418, 1988.
140) A. A. Feinberg, "Parametric Failure Rate Model for Quartz Crystal Device Aging with Application to Surface Acoustic Wave Filters," Proc. 41st Ann. Symp. on Frequency Control, pp. 360-364, 1987.
141) D. E. Beetley, "Nine-Year Aging Behavior of the Ceramic Flatpack Resonator," Proc. 3rd European Time and Frequency Forum, pp. 139-142, 1989.
142) D. E. Beetley, "Nine-Year Aging Behavior of the Ceramic Flatpack Resonator," U. S. Dept. of Energy contract report, GE Aerospace Tech. Info. Series, GEPP-TIS-1168, UC-706, March 6, 1990. Copies available from: GEND Tech. Info. Center, P.O. Box 2908, Largo, FL 34649-2908, or from NTIS.
143) A. H. Cottrell and V. Aytekin, "The Flow of Zinc Under Constant Stress," J. Inst. Metals, Vol. 77, pp. 389-422, 1950.
144) D. A. Emmons, "Tactical Quartz Oscillator Development," RADC-TR-90-232 Final Technical Report, pp. 7-30, September 1990.
145) T. R. Meeker and W. R. Grise, "Packaging and Reliability of SAW Filters," Proc. 1983 Ultrasonics Symposium, pp. 117-124, 1983.