This project is more complex than the others described earlier. However,
when finished, you will have an instrument capable of measuring all but the largest capacitors used in radio circuits.
Unlike variable resistors, most variable capacitors are not marked with their values. As well, the markings of
capacitors from salvaged equipment often rub off. By being able to measure these unmarked components, this project
will prove useful to the constructor, vintage radio enthusiast or antenna experimenter.
The common 555 timer IC forms the heart of the circuit (Figure Three). Its function is to charge the unknown capacitor
(Cx) to a fixed voltage. The capacitor is then discharged into the meter circuit. The meter measures the current
being drawn through the 47 ohm resistor. The 555 repeats the process several times a second, so that the meter
needle remains steady.
The deflection on the meter is directly proportional to the value of the unknown capacitor. This means that the
scale is linear, like the voltage and current ranges on an analogue multimeter.
The meter has five ranges, from 100pF to 1uF, selected by a five position two pole switch. In addition, there is
a x10 switch for measuring higher values and a divide-by-two facility to allow a better indication on the meter
where the capacitor being measured is just above 100, 1000pF, 0.01, 0.1 or 1 uF.
Component values are critical. For best accuracy, it is desirable that the nine resistors wired to the Range switch
have a 2% tolerance. If 0A47 diodes are not available, try OA91 or OA95 germanium diodes instead. Construct the
meter in a plastic box; one that is about the size of your multimeter but deeper is ideal. The meter movement should
as large as your budget allows; you will be using it to indicate exact values. A round 70mm-diameter movement salvaged
from a piece of electronic equipment was used in the prototype. The meter you buy will have a scale of 0 to 50
microamps. This scale needs to be converted to read 0 to 100 (ie 20, 40, 60, 80, 100 instead of 10, 20, 30, 40,
50). Use of white correction fluid or small pieces of paper will help here.
The components can be mounted on a piece of matrix board or printed circuit board. Use a socket for the IC should
replacement ever be needed. Keep wires short to minimise stray capacitance; stray capacitance reduces accuracy.
Calibrating the completed meter can be done in conjunction with a ready-built capacitance meter. Failing this,
a selection of capacitors of known value, as measured on a laboratory meter, could be used. If neither of these
options are available, simply buy several capacitors of the same value and use the one which is nearest the average
as your standard reference. Use several standards to verify accuracy on all ranges.
To calibrate, disable both the x10 and divide-by-two functions (ie both switches open). Then connect one of your
reference capacitors and switch to an appropriate range. Vary the setting of the 47k trimpot until the meter is
reading the exact value of the capacitor. Then switch in the divide-by-two function. This should change the reading
on the meter. Adjust the 10k trimpot so that the needle shows exactly twice the original reading. For example,
if you used a 0.01 uF reference, and the meter read 10 on the 0.1 uF range, it should now read 20. Now switch out
the divide-by-two function.
If you are not doing so already, change to a reference with a value equal to one of the ranges (eg 1000pF, 0.01uF,
0.1uF etc). Switch to the range equal to that value (ie the meter reads full-scale (100) when that capacitor is
being measured. Switching in the x10 function should cause the meter indication to drop significantly. Adjust the
470 ohm trimpot so that the meter reads 10. Move down one range (eg from 0.01uF to 1000pF). The meter should read
100 again. If it does not, vary the 470 ohm trimpot until it does. That completes the calibration of the capacitance
meter. Now try measuring other components to confirm that the measurements are reasonable.
With care, an accuracy of five percent or better should be possible on most ranges.
Reference :
Hawker, P Amateur Radio Techniques, Seventh Edition, RSGB, 1980
Last
Updated : February 15, 2002 