A crystal set detector may be simulated in Spice by using a voltage source V1 feeding a parallel tuned circuit L1|C1 through a source resistance R1.  The parallel tuned circuit may be made to have any Q by placing a parallel resistor across the tuned circuit.  In the simulation circuit files enclosed, an infinite Q is assumed (no RF tuned circuit losses).  The actual source loaded Q of the tuned circuit is R1/(Reactance of C1 at resonance).  The voltage at the hot end of the tuned circuit is connected through a diode D1 to a parallel RC load R2|C2.  The detected output voltage is developed across this load. The purpose of doing this is to enable experimentation to determine how the detection sensitivity changes if the diode type, diode source resistance, and/or load resistance are changed.  This program enabled me to develop the graphs shown in Article #1 on my home page that show how detector power loss varies as a function of rectified diode current for a HP 5082-2835 diode and also, more importantly, as a function of diode saturation current Is.  The input voltage is modeled as an unmodulated 1.0 MHz sine wave consisting of 4002 individual cycles, sampled at eight points per cycle. If one wants to evaluate the result of using an AM modulated wave, three simulations can be made using min., carrier, and max. Voltage levels of the desired modulated wave.

One of the simulations in the enclosed Zip archive 'Crystal Set SPICE Simulations' (click here) uses a Spice model of a Schottky diode similar to the HP 5082-2835.  This is called simulation XtlSetSim1 and its files are contained in the directory XtlSetSim1.  The other simulation uses a Spice model of the 1N34A.  This is called simulation XtlSetSim2 and its files are in the directory called XtlSetSim2.  Each of these directories contains all the files that were generated by my SPICE simulator when I ran each simulation.  The diodes used in each of these models have the value of CJO set to 0.0 pF.  This does not effect the simulation and makes it easier to experiment with various values of C2 without the detuning effect of CJO.  The input source and output load resistance values are equal and match the diode RF input impedance and audio output impedance values.  This condition gives the lowest loss (highest Xtal Set sensitivity) at low signal power levels..

In XtlSetSim1 the input sine wave voltage is set to a peak value of 0.1 volts.  Since the source resistance is set to 700,000 ohms, the power incident on the detector is -57dBm.  The output power delivered to R2 is -68dBm.  A broadcast AM voice signal, if it developed a peak instantaneous power in the detector load of -68dBm, would be just sufficient to enable me to understand about one half the words.  This assumes that I am using headphones of an equivalent 700,000 Ohms AC impedance having the power sensitivity of a good real world Sound-Powered Headset.  (The 700,000 Ohm impedance, of course would be obtained with the aid of an audio transformer.)  The RMS audio power would be about 18dB less or -86dBm.  Of course, the impedance values used here are quite high, but they are the values I achieve in my loop crystal set.  To find out where the -18 dB came from, see Article #1, end of part 1, from the home page.

In XtlSetSim2 the input sine wave is set to a peak value of 0.045 volts.  Since the source resistance is set to 16,000 ohms, the power incident on the detector is -47dBm. The output power delivered to R2 is -68dBm, the same as in the XtlSetSim1 example.  The audio load used is 16k ohms. Note that the insertion loss in XtlSetSim1 is 68-57=11 dB.  The loss in XtlSetSim2 is 68-47=21 dB.  XtlSetSim1 requires 10 dB less input than XtlSetSim2 for the same output!  XtlSetSim1 uses a diode with a saturation current Is=40 nA and n=1.08. XtlSetSim2 uses a diode of Is=2600 and n=1.6.  The second graph in article #1 on this site predicts that the loss difference would be 8dB.  This experiment illustrates that a detector using a of a lower Is, if it is matched at the input and output, will have a lower loss than one using a diode of a higher Is.  I have found out, since this article was written, that in a 1N34A germanium diode, the values of Is and n change at low currents.  Is may go down as much as 5 times and n may drop 25% from the values used in simulation XtlSetSim2. (Those values were obtained at a diode current of about 320 uA.)  This was not expected from the Schottky diode equation.  The result is that the germanium diode is unfortunately shown incorrectly and in an unfavorable light.  The simulation in XtlSetSim2 should have used an Is of about 700 nA and n should have been about 1.15.

I used the SPICE program from Intusoft called ICAP4WINDOWS demo version.  It can be downloaded for free from their Website at http://www.intusoft.com.  The netlists: XtlSetSim1.cir and XtlSetSim2.cir can be edited and used in any other SPICE simulator.

Keep the following things in mind:
1. Simulations are only as good as the SPICE simulator, its device models and the circuit topology used.  The Schottky diode equation agrees well with the results from the Schottky diodes I have checked, even at low currents.  With the one germanium 1N34A I have checked, the Schottky diode equation equation works well above about 40 micro-amps but not very well below that. (for a specific voltage, the equation specifies a higher current than the diode delivers.)
2. The tuned circuit L1|C1 must be tuned to resonance.  When this is the case, the voltage across the tuned circuit will be in phase with the source voltage V1.  If the Intusoft simulator is used, the probe point for V1 is Y1 and the probe point for the tuned circuit voltage is Y2.  If one views Y1 and Y2 on the same graph one can check the relative phases of the two voltages. Y3 gives the output voltage.
3. The carrier ripple shown at the output has negligible effect on the average output.  A larger value for the filter bypass C2 can reduce the ripple, but at the expense of rise time of the output voltage.
4. When considering the practical application of simulation ideas, keep in mind the advice in articles # 1, 4 & 5 on this Website, especially as regards audio impedance matching.
5. Shown below are the schematic diagram from the schematic editor Spicenet, the simulation of all 4002 cycles of the 1.0 MHz signal at Y1, Y2 and Y3, and the last four cycles of the 1.0 MHz signal. Note that this simulation uses a Schottky diode, not a N34A diode.
 

Published: 01/02/00;  Last revision: 05/25/00