Please note this article first appeared in the July 1995 edition of MARA NEWS
Grounding Tips
Downloaded from America on Line (SWL Area)
With grounds the most common experience is "the more the merrier". As you add more, however, you usually reach a diminishing returns (no pun intended) situation where there is no *observable* improvement: That's usually a good place to stop. There are also exceptional circumstances where grounding increases noise problems, but these, in my experience, are much rarer than the pundits who preach against "ground loops" seem to think. Even a semi-quantitative theoretical treatment of grounding in oversimplified situations requires heavy math at RF. Experimentation is thus required even if one has done elaborate calculations. It's often easier to use the theory as a guide to what to try, and then experiment.
What is Ground?
If I connect the shield of my coax (which is grounded outside) to the antenna input of my receiver, I hear lots of junk, indicating that there is an RF voltage difference between the coax shield and the receiver chassis. Last night this measured about S5.5, which is about -93 dBm (preamp off, 6KHz bandwidth). That's a lot of noise: it was 18 dB above my antenna's "noise floor", and 26 dB above the receiver's noise floor.
This sort of disagreement about ground potential is characteristic of electrically noisy environments. The receiver will, of course, respond to any voltage input that differs from its chassis ground. The antenna, on the other hand, is in a very different environment, and will have its own idea of what ground potential is. If you want to avoid noise pickup, you need to deliver a signal, referenced at the antenna to whatever its ground potential is, in such a way that when it arrives at the receiver, the reference potential is now the receiver's chassis potential. Coaxial cable represents one way to do this. Coax has two key properties:
1. The voltage between the inner conductor and the shield depends only on the state of the electromagnetic field within the shield.
2. The shield prevents the external electromagnetic field from influencing the internal electromagnetic field (but watch out at the ends of the cable!).
So, it's easy, right? Run coax from the antenna to the receiver. Ground at the antenna end will be whatever the antenna thinks it is, while ground at the receiver end will be whatever the receiver thinks it is. The antenna will produce the appropriate voltage difference at the input side, and the receiver will see that voltage difference uncontaminated by external fields, according to the properties given above.
Unfortunately, it doesn't quite work that way. It's all true as far as it goes, but it neglects the fact that the coax can also guide noise from your house to your antenna, where it can couple back into the cable and into your receiver. To see how this works, let me first describe how this noise gets around.
The noise I'm talking about here is more properly called "broadband electromagnetic interference" (EMI). It's made by computers, lamp dimmers, televisions, motors and other modern gadgets. I have all these things. In many cases, I can't get them turned off, because it would provoke intrafamily rebellion. However, even when I turn them off, the noise in the house doesn't go down very much, because my neighbors all have them too. In any case, one of the worst offenders is my computer, which is such a handy radio companionI'm not about to turn *it* off.
Some of this noise is radiated, but the more troublesome component of this is conducted noise that follows utility wires. Any sort of cable supports a "common mode" of electromagnetic energy transport in which all of the conductors in the cable are at the some potential, but that potential differs from the potential of other nearby conductors ("ground"). The noise sources of concern generate common mode waves on power, telephone, and CATV cables which then distribute these waves around your neighborhood. They also generate "differential" mode waves, but simple filters can block these so they aren't normally a problem.
So, let's say you have a longwire antenna attached to a coaxial cable through an MLB ("Magnetic Longwire Balun" [sic]). Suppose your next door neighbor turns on a dimmer switch. The resulting RF interference travels out his power lines, in through yours, through your receiver's power cord to its chassis, and out your coaxial cable to your MLB. Now on coax, a common mode wave is associated with a current on the shield only, while the mode we want the signal to be in, the "differential" mode, has equal but opposite currents flowing on shield and inner conductor. The MLB works by coupling energy from a current flowing between the antenna wire and the coax shield into the differential mode. But wait a second: the current from the antenna flows on the coax shield just like the common mode current does. Does this mean that the antenna mode is contaminated with the noise from your neighbor's dimmer?
The answer is a resounding (and unpleasant) yes! The way wire receiving antennas work is by first moving energy from free space into a common mode moving along the antenna wire, and then picking some of that off and coupling it into a mode on the feedline. In this case, the common mode current moving along the antenna wire flows into the common mode of the coax, and vice versa. The coax is not just feedline, it's an intimate part of the antenna! Furthermore, as we've seen, it's connected back through your electrical wiring to your neighbor's dimmer switch. You have a circuitous but electrically direct connection to this infernal noise source. No wonder it's such a nuisance!
The solution is to somehow isolate the antenna from the common mode currents on the feedline. One common way to do this is with a balanced "dipole" antenna. Instead of connecting the feedline to the wire at the end, connect it to the middle. Now the antenna current can flow from one side of the antenna to the other, without having to involve the coax shield. Unfortunately, removing the necessity of having the coax be part of the antenna doesn't automatically isolate it: A coax-fed dipole is often only slightly quieter than an end-fed longwire. A "balun", a device which blocks common mode currents from the feedline, is often employed. This can improve the situation considerably. Note that this is not the same device as the miscalled "Magnetic Longwire Balun".
Another way is to ground the coaxial shield, "short circuiting" the common mode. Antenna currents flow into such a ground freely, in principle not interacting with noise currents. The best ground for such a purpose will be a earth ground near the antenna and far from utility lines. Still another way is to block common mode waves by burying the cable. Soil is a very effective absorber of RF energy at close range.
Unfortunately, none of these methods is generally adequate by itself in the toughest cases. Baluns are not perfectly effective at blocking common mode currents. Even the best balun can be partially defeated if there's any other unsymmetrical coupling between the antenna and feedline. Such coupling can occur if the feedline doesn't come away from the antenna at a right angle. Grounds are not perfect either. Cable burial generally lets some energy leak through. A combination of methods is usually required, both encouraging the common mode currents to take harmless paths (grounding) and blocking them from the harmful paths (baluns and/or burial).
The required isolation to reach the true reception potential of the site can be large. According to the measurements I quoted above, for my site the antenna noise floor is 18 dB below the conducted noise level at 10 MHz. 18 dB of isolation would thus make the levels equal, but we want to do better than that: We want the pickup of common mode EMI to be insignificant, at least 5 dB down from the antenna's floor. In my location