This site is hosted at WebWizards.Net for better value.
Don't leave this valuable site without visiting my book shop to see my recommendations. This helps keep this site FREE for everyone.
YOU ARE HERE: HOME > BASICS > MOBIUS WINDING TECHNIQUES
Mobius winding techniques are a method of winding inductors, loop antennas specifically, to reduce the self capacitance inherent in the windings. Any inductor exhibits capacitance between windings, that's a fact of life. This capacitance in conjuction with the inductance forms a "self resonant frequency" for your loop or inductor. A loop antenna is simply another inductor by the way. For tuneable loops the inductance can be so high as to limit the useful frequency range and here mobius winding techniques can really help out.
Unfortunately this is a little hard to explain, so let's use an example of a loop antenna constructed in a piece of aluminium channel. Our aluminium channel is fabricated into a rectangle as in figure 1a below. The loop is depicted in figure 1b, O.K. I don't win any drawing prizes.
The reason for the aluminium channel I'll explain much later, but it's important.
Figure 1. - loop antenna constructed in a piece of aluminium channel
For a square loop, imagine you had a piece of aluminium channel 20 mm X 20 mm (3/4" X 3/4") and 1200 mm (4') long. This is cut to have slots (blade width) through the sides only at about 300 mm (1') intervals so the channel can be bent back to form a perfect square.
Normally you would wind your wire around the loop so that each insulated winding is adjacent to one another, as sort of depicted in figure 1a and 1b.
A mobius winding technique, actually alternates the windings.
As I said, the mobius winding method, actually alternates the windings. It is said that except for start and finish where wires cross, all the "odd numbered wires" are adjacent to one another i.e. turns 1, 3, 5, 7..... Similarly, all the "even numbered wires" are adjacent to one another i.e. turns 2, 4, 6, 8..... That's the mobius winding technique.
Difficult to explain, impossible to depict with my drawing skills, I'll try.
Using the mobius winding method, you would wind turn 1 all around the loop hard up against say the left hand side of the channel. When you get back to start to do the next turn, you cross over so that turn 2 is hard up against the right hand side of the channel. Cross over again when doing turn 3 to the left side adjacent to turn 1 and so on until you have the desired number of turns.
The immediate benefit of the mobius winding method is the self-capacitance of the windings are reduced by about 50% leading to something like a four fold increase in the self resonant frequency. A further benefit is a broadening of the bandwidth of the loop. There is some reduction in the final inductance compared to a similar conventional loop of equivalent turns.
Good question! When I get around to loop antennas I'll cover it in more detail. For the moment, shielded loops (electrostatic shielding) respond favourably to the magnetic component of an incoming wave (signal) and eliminates the "antenna effect". This is also called electrostatic balance. The object of the exercise here is to improve the directivity of the loop which is usually the purpose of constructing a loop in the first place. They are however quite inefficient and probably -25 dB below a conventional antenna in performance.
The mobius winding technique improves the performance of a directional loop antenna, particularly at lower frquencies where conventional directional antennas would be impossible to construct physically.
The centre of a shielded loop antenna is always insulated to prevent it becoming a shorted turn.
This site is hosted at WebWizards.Net for better value.
As you would imagine maintaining this site costs me considerable sums of money in many, many ways. If you believe this site is a valuable and FREE educational resource and, YOU want to keep it that way, then here's how YOU can demonstrate your very practical support for this site..
Thanks to these fine folks making voluntary donations, ensuring this site and our Newsletter remains FREE. Could YOU be listed here for your small contribution in return for your FREE education?. Our grateful thanks.
Please send me your valuable comments and suggestions! Tell your friends, tell a news group, tell your favourite magazine, heck tell the world!
Absolutely essential to keeping abreast of new and updated electronics tutorials is our comments or subscribe to our highly regarded FREE monthly newsletter form. Unsubscribe any time you like. You can view immediate past issues here to see if it is to your liking.
the author Ian C. Purdie, VK2TIP of www.electronics-tutorials.com asserts the moral right to
be identified as the author of this web site and all contents herein. Copyright © 2000, all rights reserved. See copying and links.
These electronic tutorials are provided for individual private use and the author assumes no liability whatsoever for the application, use, misuse, of any of these projects or electronics tutorials that may result in the direct or indirect damage or loss that comes from these projects or tutorials. All materials are provided for free private and public use.
Copyright © 2000, all rights reserved. URL - www.electronics-tutorials.com/basics/mobius-winding.htm
Updated 17th November, 2000
What are mobius winding techniques?
How is a mobius winding technique implemented?
The mobius winding technique
What's the benefits of the mobius winding technique?
Why use aluminium channel and a mobius winding technique for the loop antenna?
CARE TO BE A PRACTICAL SUPPORTER OF THIS SITE?
Commercial use prohibited without prior written permission from www.electronics-tutorials.com.