MAR-7
Frequency
MHz
GAIN, dB Maximum Power, dBm Dynamic Range VSWR Absolute
Maximum
Rating
DC Power Thermal
resistance
Øjc
°C/W
fL - fU Min. Output
(1 dB
Comp.)
Input
(no
damage)
NF
dB
Typ.
IP3
dBm
Typ.
In
Typ.
Out
Typ.
I
(mA)
P
(mW)
Cur-
rent
(mA)
Volt(V.)
DC-2000 9.00 +5.50 +13.00 5.00 19.00 1.40 1.50 60.00 275.00 22.00 4.00 110.00
Lw=low range(fL to fU/2)  U=upper range(fU/2 to fU)

Pin Connections
Port RF in RF Out DC Case GND Not Used
cb 1 3 3 2,4 -



Case Style - VV105 (inch,mm )   weight: 0.015 grams.
A B C D E F G H J
.085
2.159
.060
1.524
.008
0.203
.020
0.508
.256
6.502
.012
0.305
.025
0.635
   
K L M N P Q R S T
                 
Tolerance: .x ± .1  .xx ± .03  .xxx ± .015 inch.
Material and Finish:
    Case material: plastic. Lead Finish: tin-lead plate.
Marking:
    RF input lead (1) identified by one or both of the following at factory option:
(a) diagonally cut lead, which may be 45°(ref) in either direction;
(b) orientation mark on the case. Model dash number identified by color dot or alphanumeric code on case. See specification data sheet.
Special Tolerances:
    Lead width ±.010; lead thickness ±.005 inch.

Notes:
• Minimum gain at highest frequency. Full temperature range, except room temperature for Dash-4 models.
• Frequency at which output power, NF and IP3 are specified: 1000 MHz.
• Thermal resistance Øjc is from hottest junction in the device to the mounting surface of the leads.
• Model number designated by alphanumeric code marking.
• Permanent damage may occur if any of these limits are exceeded. These ratings are not intended for continuous normal operation.
• For Amplifier Selection Guide, please click here.
For Amplifier Environmental Specifications, please click here.
• For Surface Mount Environmental Specifications, please click here.
Re-flow soldering information is available in "Surface Mount" article.
• Low frequency cutoff determined by external coupling capacitors.
• Non-hermetic
• Typical Biasing Configuration ERA/MAR/MAV/RAM/VAM
• Prefix letter (optional) designates assembly location.
• Reliability predictions and normal operation conditions are applicable at current specified.
• General Quality Control Procedures and Environmental Specifications are given in Mini-Circuits Guarantees Quality.
Hi-Rel, MIL description are given in Hi-Rel and MIL
• Prices and Specifications subjects to change without notice.

FREQ
(MHz)
S11 (Input Return Loss) S21 (Power Gain) S12 (Isolation Out-in) S22 (Output Return Loss)
dB Mag Ang dB Ang dB Mag Ang dB Mag Ang
100.00 -26.02 0.05 169.00 13.50 173.00 -19.17 0.11 1.00 -17.08 0.14 -7.00
500.00 -30.46 0.03 133.00 13.10 150.00 -18.42 0.12 6.00 -17.72 0.13 -41.00
1000.00 -40.00 0.01 58.00 12.50 122.00 -17.72 0.13 10.00 -19.17 0.11 -94.00
1500.00 -24.44 0.06 -113.00 11.80 95.00 -16.48 0.15 10.00 -17.72 0.13 -148.00
2000.00 -16.48 0.15 -144.00 10.50 70.00 -15.39 0.17 7.00 -15.39 0.17 174.00
2500.00 -11.37 0.27 -165.00 9.60 48.00 -14.89 0.18 1.00 -14.42 0.19 154.00
3000.00 -8.64 0.37 169.00 8.10 27.00 -13.98 0.20 -6.00 -14.89 0.18 144.00
3500.00 -6.94 0.45 150.00 6.50 10.00 -14.42 0.19 -11.00 -15.39 0.17 144.00
4000.00 -5.98 0.51 134.00 5.00 -4.00 -14.42 0.19 -15.00 -15.39 0.17 152.00